FUME HOOD (UET-501)

 Fume hoods are designed to function as an enclosed ventilated workspace- can provide a substantial degree of protection to user. It is designed so as to throw-out all toxic harmful vapour, acidic/alkaline fumes, chemical vapors, removal of odour from the hood working area.

MOC: GI Powder Coated / Stainless Steel / Polypropylene

Type: Floor Standing Model / Table Top Model

Working Area WxDxH : 600x600x900mm, 600x600x1200mm, 600x600x1800mm

Bottom Arrangements: Cabinets, With Cupboard With One Horizontal Partition and Shutters,

Locking Arrangements.

Baffles: Aerodynamic Shape Fully Made Of 3mm FRP.

Work Top: Black Granite 18mm.

Sash Shutter: Single, Vertical Sliding, Balanced With Counter Weight.

Blower Type: Centrifugal Blower

Powered By: 1 HP 1440 RPM Single Phase.

Exhaust Duct: PVC/FRP Duct Pipe

Electrical Arrangements: 2 Nos. 15/5 Amps 3 Pin Socket

Illumination: By 4 Feet Tube Light.

Sink & Tap: Sink With Outlet Nipple Single Way / Three Way Swan Neck Tap

DUCTLESS FUME HOOD(UET-502)

 Constructions: Mild Steel / Stainless Steel-304

Table: Stainless steel sheet of 304 grade/ fortified acid proof glazed tiles

Sink: Stainless steel sink with tap

Coating: Epoxy Coating

Air Flow: Unidirectional

Air Flow Velocity: 0.4m/sec

Air Flow Control: Three step air flow speed controller

Blower Assembly: Centrifugal lubricated bearing type ISI marked assembly

Illumination: Fluorescent light illumination greater than 800 lux on work table.

Noise Level: Noise level less than 60 dB

Nominal Voltage: 220- 230 Volts Single Phase

Working Size: 4’ x 2’ x 2’ / 4’ x 2.5’ x 2.5’ / 5’ x 2.5’ x 2.5’

WET BENCH FUME HOOD(UET-503)

 Construction: All stress-relieved white polypropylene, 0.5" (13 mm) thick or all 304 stainless steel.Standard plumbing is PVC (specify 304 stainless steel or other desired material).

Exhaust: Ducted through a standard 10" (254 mm)-diameter flange positioned at the top rear of the cabinet (see airflow illustration). Specify other desired flange diameter or location.

Drain: 2" NPT female, located at bottom of sub-deck plenum.

Power: 120VAC, 60Hz or 220VAC, 50Hz, depending on component selection. Power outlets available for process equipment.

Illuminator: 800 lux 

Controls: Instrument panel provides power switch, power indicating light, light switch, static pressure exhaust meter, and power fuse. Provisions are made for audible and visible pressure alarm, visible alarm silence, and for control of optional processing baths.

Noise Factor: 50 dBA

Filter Type: 99.99% efficient HEPA

Air Flow: Unidirectional

Air Flow Control: Three Step Air Flow Speed Controller

Blower Assembly: Centrifugal lubricated bearing type ISI marked assembly

Nominal Voltage: 220- 230 volts, 50Hz single phase  

TABLE TOP FUME HOOD(UET-504

Constructions: Mild Steel / Stainless Steel-304

Table: Stainless steel sheet table of ss-304 grade/ fortified acid proof glazed tiles

Coating: Epoxy coating/ FRP lined

Air flow: Unidirectional

Blower assembly: Centrifugal lubricated bearing type ISI marked assembly

Illumination: Fluorescent light illumination greater than 800 lux on work table.

Noise level: less than 60 db

Power requirements: 500 watts -750 watts( model specific)

Nominal voltage: 220- 230 volts, 50Hz single phase

Frequency: 50

Working Size: 4’ x 2’ x 2’ / 5’ x 2’ x 2’ / 6’ x 2’ x 2’ / 7’ x 3’ x 3’ / 8’ x 3’ x 3’

POLYPROPYLENE FUME HOOD(UET-505)

Exterior and interior construction: Structural polypropylene

Exhaust: 500 cFM-1250cFM Static

Exhaust: 20mm-38mm

Exhaust Duct: 102*610 mm

Down Flow Velocity 105 LFPM: 60 LFPM (0.30 m/s)

Inflow Velocity: 105 LFPM (0.53 m/s)

Power Requirements: 230V, 50 Hz

Working Size: 4’ x 2’ x 2’ / 5’ x 2’ x 2’ / 6’ x 2’ x 2’ / 7’ x 3’ x 3’ / 8’ x 3’ x 3’

FUME HOOD SCRUBBER (UET-506)

Constructions: Thick PCRC, pre coated corrosion resistant GI sheet

Table: Stainless steel sheet table of 304 grade/ fortified acid proof glazed tiles

Sink: Stainless steel sink with tap

Coating: Epoxy coating/ FRP lined

Air flow: Unidirectional

Air flow control: Three step air flow speed controller

Blower assembly: Centrifugal lubricated bearing type ISI marked assembly

Illumination: Fluorescent light illumination greater than 800 lux on work table.

Noise level: Noise level less than 60 db

Nominal voltage: 220- 230 volts, 50Hz single phase

Working Size: 4’ x 2’ x 2’ / 4’ x 2.5’ x 2.5’ / 5’ x 2.5’ x 2.5’ / 6’ x 2.5’ x 2.5’ / 6’ x 3’ x 3’